Replacing the tie rod end on a 1964 Jeep CJ-5A can seem daunting, but with a little patience and the right tools, you can do it yourself. click here for more details on the download manual…..

1972 Jeep CJ5 Rear underside around rear driveshaft 1972 Jeep CJ5 Rear underside around rear driveshaft.

Re-Wiring Your Old Jeep EP1 Need to rewire your Jeep but on a tight budget? Here I use the EZ-Wire brand 12 circuit universal kit which sells for under $200 …

Here’s a simple step-by-step guide:

### tools and Materials Needed:
1. **Wrench set** (usually 7/16” or 1/2” depending on your jeep)
2. **Socket set**
3. **Pry bar or hammer**
4. **Tie rod end replacement part**
5. **Grease or grease gun**
6. **Safety glasses**
7. **Jack and Jack stands** (to lift the vehicle safely)
8. **Pliers** (if needed)

### Step-by-Step Guide:

#### 1. Safety First
– **Park the Jeep on a flat surface** and engage the parking brake.
– **Wear safety glasses** to protect your eyes from any debris.

#### 2. Lift the Vehicle
– Use a **jack** to lift the front of the Jeep and secure it with **jack stands**. This allows you to work safely underneath.

#### 3. Locate the Tie Rod End
– The tie rod end is part of the steering system and connects the steering linkage to the wheel. It’s typically found near the front wheels and looks like a small metal ball joint.

#### 4. Remove the Wheel (Optional)
– For easier access, you might want to remove the wheel by loosening the lug nuts and taking the wheel off.

#### 5. Disconnect the Tie Rod End
– **Locate the nut** that secures the tie rod end to the steering knuckle (the part that holds the wheel).
– Use the appropriate **wrench or socket** to remove this nut. Be careful not to strip it.

#### 6. separate the Tie Rod End
– After removing the nut, you’ll need to separate the tie rod end from the steering knuckle. you can use a **pry bar** or gently tap around the area with a **hammer** to help it pop out. Be cautious to avoid damaging other components.

#### 7. Remove the Old Tie Rod End
– Once separated, you can unscrew the tie rod end from the tie rod itself. This may require turning it counterclockwise.

#### 8. Install the New Tie Rod End
– Take the new tie rod end and screw it into the tie rod, turning it clockwise. Make sure it’s tight.
– Reattach it to the steering knuckle and secure it with the nut you removed earlier. Tighten it well, but do not over-tighten.

#### 9. Grease the New Tie Rod End
– If your new tie rod end comes with a grease fitting, use a **grease gun** to apply grease. This helps ensure smooth operation and longevity.

#### 10. Reattach the Wheel (if removed)
– If you took off the wheel, put it back on and tighten the lug nuts.

#### 11. Lower the Vehicle
– Carefully remove the Jack stands and lower the vehicle back to the ground.

#### 12. Test the Steering
– Once everything is back in place, turn the steering wheel left and right to ensure everything is functioning properly. Take a short drive to check for any unusual noises or handling issues.

### Final Tips:
– Always refer to your Jeep’s manual for specific torque specifications and details.
– If you’re unsure about any step, don’t hesitate to ask for help or consult a professional.

By following these steps, you should be able to replace the tie rod end on your Jeep CJ-5A successfully! Good luck!
Brake cleaner is a specialized solvent designed to clean components of a vehicle’s brake system, including brake pads, rotors, calipers, and drums. It plays a vital role in maintaining the efficiency and safety of a vehicle’s braking system. The primary purpose of brake cleaner is to remove contaminants such as dust, grease, oil, and brake fluid, which can accumulate over time and impair the performance of the brakes.

Typically available in aerosol cans, brake cleaner features a powerful solvent that evaporates quickly, ensuring that it leaves no residue behind. This is crucial because any leftover substance can interfere with the friction needed for effective braking. Brake cleaner is often composed of various chemicals, including acetone, toluene, or other petroleum-based solvents. These ingredients work together to break down stubborn grime and debris.

Using brake cleaner is straightforward. It is essential to ensure that the vehicle is safely raised and properly secured before application. The cleaner is usually sprayed directly onto the components that need cleaning. For thoroughness, it might be necessary to scrub with a brush or cloth, especially in areas with heavy buildup.

Additionally, brake cleaner is flammable and should be used in well-ventilated areas, away from open flames or sparks. Mechanic shops and DIY enthusiasts frequently rely on brake cleaner to keep braking systems in optimal working condition, thus enhancing vehicle safety on the road.