Replacing the clutch plate on a Dodge Stratus involves several detailed steps and requires specific tools. click here for more details on the download manual…..

How to Replace Exterior Door Handle 01-06 Dodge Stratus Buy Now! New Exterior Door Handle from 1AAuto.com http://1aau.to/ib/1ADHE00347 1A Auto shows you how to repair, install, fix, …

"Dodge Stratus" rear shocks | Full video link below This 2004 Dodge Stratus sedan will be receiving new rear shocks in this video. Below is the link. Thanks for watching.

Below is a comprehensive guide to help you with this process.

### Tools and Equipment Needed
– **Basic Hand Tools:**
– **Socket Set:** Metric sockets (typically 10mm to 18mm) for removing bolts.
– **Wrench Set:** Adjustable wrench or combination wrenches for various sizes.
– **Ratchet and Extensions:** To reach bolts in tight spaces.

– **Specialized Tools:**
– **Clutch Alignment Tool:** Helps align the new clutch plate with the flywheel during installation.
– **Torque Wrench:** Ensures that bolts are tightened to the manufacturer’s specifications.
– **Flywheel Holding Tool:** Helps prevent the flywheel from spinning during bolt removal.

– **Safety Equipment:**
– **Jack and Jack Stands:** To lift and securely support the vehicle.
– **Safety Glasses:** Protects eyes while working.

– **Other Supplies:**
– **Clutch Kit:** Includes clutch plate, pressure plate, and release bearing.
– **Transmission Fluid:** To refill after completing the job.
– **Grease:** For lubricating the release bearing and other moving parts.

### Procedure
– **Preparation:**
– **Park the Vehicle:** Ensure the car is on a flat surface and in gear (or park for automatic).
– **Disconnect the Battery:** Remove the negative terminal to prevent electrical shorts.

– **Lifting the Vehicle:**
– **Jack Up the Car:** Use a floor jack to lift the front of the vehicle.
– **Secure with Jack Stands:** Place jack stands under the appropriate frame points for safety.

– **Removing the Transmission:**
– **Drain Transmission Fluid:** Place a pan under the transmission and remove the drain plug.
– **Remove the Drive Shafts:** Unbolt the drive shafts from the transmission and set them aside.
– **Disconnect Linkages:** Unbolt and disconnect the clutch pedal linkage and any other necessary linkages.
– **Detach the Transmission:** Remove bell housing bolts and carefully slide the transmission off the engine. You may need to use a transmission jack for support.

– **Inspecting Components:**
– **Check Flywheel Condition:** Look for cracks, warping, or excessive wear. Resurface or replace if necessary.
– **Inspect Other Parts:** Check the release bearing and pilot bearing for wear.

– **Removing the Old Clutch:**
– **Unbolt the Pressure Plate:** Remove the bolts securing the pressure plate to the flywheel.
– **Take Out the Clutch Plate:** Carefully slide out the old clutch plate from between the flywheel and pressure plate.

– **Installing the New Clutch:**
– **Position the New Clutch Plate:** Use the clutch alignment tool to center the new clutch plate against the flywheel.
– **Attach the Pressure Plate:** Secure the new pressure plate to the flywheel with bolts, tightening them in a crisscross pattern to ensure even pressure.

– **Reinstalling the Transmission:**
– **Align the Transmission:** Carefully slide the transmission back into place, ensuring it aligns with the engine and clutch components.
– **Reattach Bell Housing Bolts:** Tighten all negative battery terminal.
– **Lower the Vehicle:** Carefully remove jack stands and lower the vehicle with the jack.

– **Testing:**
– **Start the Vehicle:** Check for any unusual noises or issues.
– **Test the Clutch:** Press the clutch pedal and shift through the gears to ensure proper engagement and operation.

### Conclusion
Replacing the clutch plate on a Dodge Stratus requires careful attention to detail and the right tools. Following these steps will help ensure a successful installation. Always consult the vehicle’s service manual for specific torque requirements and additional guidance. If you are unsure about any step, it’s advisable to seek assistance from a professional mechanic.
The term “polish” in the context of automotive care refers to a product or process used to enhance the appearance of a vehicle’s paint surface. Polish is primarily designed to remove imperfections such as swirl marks, fine scratches, oxidation, and other blemishes that can accumulate over time due to environmental exposure and regular wear and tear. It typically contains abrasives that help to smooth out the paint surface, restoring its clarity and depth.

There are various types of polishes available, formulated for different purposes and paint conditions. For instance, some polishes are more aggressive and are used for heavy correction, while others are finer and intended for a lighter touch-up or maintenance routine. The application of polish can significantly improve the aesthetic appeal of a car, giving it a glossy, showroom-quality finish.

Using polish usually involves a few key steps. First, the vehicle is thoroughly washed and dried to remove any dirt and debris. Next, the polish is applied, often using a microfiber cloth or a dual-action polisher for even application. The polish is then worked into the paint using a circular motion, allowing the abrasives to level out the surface imperfections. Finally, the excess polish is wiped away, revealing a smooth and shiny finish.

Routine polishing is an essential part of vehicle maintenance, as it not only enhances appearance but also protects the paint By creating a smoother surface that can repel contaminants. Additionally, polishing can be followed By the application of wax or sealant to provide further protection and enhance the shine, ensuring that the vehicle maintains its aesthetic appeal over time.