Replacing the MacPherson strut on a Mitsubishi Lancer Evolution IV or V involves several steps that can be quite intricate. click here for more details on the download manual…..

Built Mitsubishi Evo IV Daily! | Worth The Headache? Welcome! Today we’re going for a quick drive in a modified Mitsubishi Evo IV and getting to know the ins and outs of ownership a …

Lancer Evo 4 Brakes Ruined!? Project Coupe Tiburon AWD Brake System Update We didn’t destroy the Evo 4 brakes. We merely massaged them with an angle grinder. It would have been less sketchy if we knew …

Below is a reverse order guide to help you understand the process clearly. Please Remember to follow safety protocols, use proper tools, and consult a service manual for detailed specifications.

### Steps in Reverse Order:

1. **Reassemble the Wheel and Lower the Vehicle**
– Place the wheel back onto the hub and hand-tighten the lug nuts.
– Lower the vehicle back to the ground and torque the lug nuts to the manufacturer’s specifications.

2. **Reconnect the Brake Line and ABS Sensor (if applicable)**
– Reattach the brake line bracket to the strut.
– Reconnect any ABS sensors or wiring harnesses that were disconnected.

3. **Reattach the Lower Control Arm**
– Align the lower control arm with the strut and Insert the bolts.
– Tighten the bolts to the specified torque settings.

4. **Install the strut Assembly into the strut Mount**
– Position the strut assembly into the strut mount on the vehicle’s chassis.
– Insert and tighten the bolts securing the strut to the mount on the top side of the strut.

5. **Install the strut to Steering Knuckle**
– Align the strut with the steering knuckle.
– Insert the bolts and nuts to secure the strut to the steering knuckle and tighten them to the manufacturer’s specifications.

6. **Disconnect the Old Strut**
– Remove any nuts, bolts, or clips securing the strut to the steering knuckle and lower control arm.
– Detach any components that might obstruct the removal of the strut, like brake lines or ABS sensors.

7. **Remove the strut Assembly**
– Support the lower control arm with a jack or stand.
– Carefully pull the strut assembly out from the vehicle, ensuring you don’t damage surrounding components.

8. **Disassemble the strut Assembly (if reusing components)**
– Use a strut spring compressor to safely compress the spring.
– Remove the top strut mount and bearing, then take off the spring from the strut.

9. **Prepare the New or rebuilt Strut**
– If using a new strut, ensure it’s ready for installation.
– If reusing the old strut, install the spring onto the new strut using the spring compressor, and reattach the top mount.

10. **Gather Tools and Parts**
– Ensure you have all necessary tools (wrenches, ratchets, strut spring compressor, torque wrench) and new parts (struts, mounts, bolts).

### Safety Precautions:
– Always wear safety goggles and gloves when working on vehicles.
– Make sure the vehicle is on a stable surface and use jack stands when lifting.
– Follow the manufacturer’s service manual for specific torque settings and specifications.

### Final Note:
This guide provides a reverse order of the procedure for macpherson strut replacement. It’s essential to consult the specific repair manual for the Mitsubishi Lancer Evolution IV or V for any unique details, torque specifications, and safety recommendations specific to your vehicle.
The heater control valve is a critical component of a vehicle’s heating and cooling system, primarily responsible for regulating the flow of engine coolant to the heater core. The heater core functions much like a small radiator, allowing warm air to be distributed into the cabin of the vehicle when heating is required. The heater control valve is typically installed in the coolant line that leads to the heater core and is operated either manually via a cable or electronically By the vehicle’s climate control system.

When the driver adjusts the temperature settings inside the car, the heater control valve opens or closes to either allow or restrict the flow of hot coolant. When open, the hot coolant flows into the heater core, where it transfers heat to the air blown through the core By the vehicle’s blower fan. This process generates warm air that is directed into the passenger compartment, providing comfort during colder months.

In modern vehicles, the heater control valve may be integrated with more complex climate control systems, such as dual-zone or automatic climate control, which allow for personalized temperature settings for different areas of the vehicle. If the heater control valve fails, it can lead to issues such as inadequate cabin heating, overheating of the engine, or coolant leaks, making it essential for vehicle maintenance and repair. Regular inspection and timely replacement of a faulty heater control valve are crucial for maintaining optimal performance of the vehicle’s heating system.