Replacing the Positive Crankcase Ventilation (PCV) valve on a Daewoo Doosan 430 Series 440 Plus 450 Series 460 Skid Steer Loader is a task that requires some basic tools and a bit of patience. click here for more details on the download manual…..

Doosan Daewoo 440 Plus skid steer for sale | no-reserve Internet auction September 6, 2017 https://www.purplewave.com/auction/170906/item/DC5475?utm_source=YouTube&utm_medium=video&utm_campaign=170906 …

The PCV valve is an important component that helps manage engine emissions by allowing gases from the crankcase to be recirculated into the intake manifold. Here’s a simple step-by-step guide to help you through the process.

### Tools and Materials Needed:
– New PCV valve (make sure it’s the correct one for your model)
– Socket set or wrenches
– Screwdriver (flathead or Phillips, depending on your vehicle)
– Pliers
– Clean rags or paper towels
– Safety gloves and goggles

### Steps to Replace the PCV Valve:

1. **Safety First**:
– Ensure the skid steer is turned off and parked on a flat surface.
– Allow the engine to cool if it has been running.
– Wear safety gloves and goggles to protect yourself from debris and fumes.

2. **Locate the PCV Valve**:
– Open the hood or engine cover of the skid steer to access the engine compartment.
– The PCV valve is typically located on or near the engine block. Look for a small, cylindrical component that is connected by hoses. It may be secured with a clip or a rubber grommet.

3. **Remove the Old PCV Valve**:
– Carefully disconnect the hose(s) attached to the PCV valve. You may need to use pliers to loosen any clamps holding the hoses in place.
– Once the hoses are removed, you can pull the old PCV valve out. If it’s stuck, gently twist and pull it. Be careful not to break anything.

4. **Inspect the Old Valve**:
– Take a moment to inspect the old PCV valve. If it looks clogged or dirty, that’s a sign it needed replacement. Compare it to the new valve to ensure they are the same size and shape.

5. **Install the New PCV Valve**:
– Insert the new PCV valve into the same location where the old one was. Make sure it fits snugly.
– Reattach the hoses you removed earlier. Ensure they are securely fastened and there are no air leaks.

6. **Check Everything**:
– Before closing the engine cover, double-check that the PCV valve is properly installed and that all hoses are connected correctly.
– Make sure there are no tools left in the engine compartment.

7. **Test the Machine**:
– Start the engine and let it run for a few minutes. Listen for any unusual noises and check for any leaks around the new PCV valve.
– If everything sounds and looks good, you’re all set!

8. **Close Up**:
– Once you’re satisfied that the new PCV valve is functioning correctly, close the engine cover and secure it.

### Maintenance Tip:
Regularly check your PCV valve as part of your machine’s maintenance routine. A clogged or malfunctioning PCV valve can lead to engine problems, so it’s a good idea to inspect it during oil changes or scheduled maintenance.

By following these steps, you can successfully replace the PCV valve on your Daewoo Doosan skid steer loader! If you encounter any issues or are unsure at any point, don’t hesitate to consult your operator’s manual or seek assistance from a professional.
The brake caliper is a crucial component of a disc brake system, primarily found in modern vehicles. Its primary function is to house the brake pads and exert pressure on them to create friction, which slows down or stops the vehicle. The caliper operates by using hydraulic force generated by the brake fluid, which is activated when the driver presses the brake pedal.

Typically made from aluminum or cast iron for strength and lightweight properties, the brake caliper is positioned over the brake disc (or rotor). It consists of two main types: fixed and floating (or sliding) calipers. A fixed caliper has pistons on both sides of the disc, providing more uniform pressure and better performance, while a floating caliper has a single piston that pushes the brake pad against the rotor, allowing the caliper to slide and accommodate the wear of the pads.

Inside the caliper, several pistons are activated as brake fluid enters from the master cylinder through the brake lines. This action forces the brake pads against the spinning rotor, generating the necessary friction to decelerate the vehicle. Additionally, brake calipers often come equipped with features like heat shields to dissipate heat generated during braking and anti-rattle clips to minimize noise.

Maintenance of brake calipers is essential for vehicle safety and performance. Over time, calipers can suffer from issues such as corrosion, leaks, or stuck pistons, which can lead to uneven braking or reduced stopping power. Regular inspection and timely replacement of brake components, including the caliper, are vital for ensuring the safety and efficiency of a vehicle’s braking system.